A lawn for example in Salt Lake City in San Diego card ought to be included among the essential tools in any gardener’s Stump Removal tips Littleton, CO front yard Bakersfield shed, but a homemade cart could be the best option if you want to avoid the high cost of carts offered at Grass Care front yard Littleton backyard Littleton centers. Unlike a wheelbarrow, which functions the same essential function, a Lawn Care business Phoenix, AZ Care near me Bakersfield cart has 2 wheels to make it easier to maneuver and balance. This Lawn Care service Fort Lauderdale, FL estimates Bakersfield, CA cart lots from the back for easy loading and dumping as you push it around the lawn (San Diego, CA) for example in Salt Lake City, whether you are spreading fresh mulch on flower beds or collecting fallen twigs after a storm.

Measure and cut a piece of 3/4-inch thick, pressure-treated plywood to 36 by 30 inches to your cart bottom. Cut one slice 30 by 16 inches to the front and 2 more pieces the exact same size for the sides. Measure up about 6 inches along the 16-inch side of the side pieces and cut off the corner in a 45-degree angle starting from that mark.

Prop up the 2 sides pieces together with the 30-inch sides running from front to rear and place the front piece between them with the 30-inch side running left to right. Square up the pieces so that they form a three-sided box with the angled cuts in the back of the structure. Drive 1-1/2-inch wood screws spaced 4 inches apart from the side pieces and into the sides of the front piece.

Cut 2 2-by-2-inch boards to 16-inch lengths. Stand the boards erect in the corners where the sides meet the leading part of plywood. Drive 1-1/2 wood screws through the plywood sides and into the 2-by-2-inch boards, which helps brace the cart corners. Space screws 4 inches apart.

Flip the structure upside down. Lay the cart bottom bit on top, lining it up with the front piece so the extra 6 inches of length goes past the ends of the side pieces. Drive 1-1/2-inch wood screws each 4 inches throughout the bottom of the cart bottom bit and into the narrow borders of the side and front pieces.

Cut three pieces of 1-by-4-inch lumber to 30-inch lengths. Lay these brace boards throughout the bottom in the front, middle and back of the cart; line up the back brace where the side pieces end rather than in the rear of the bottom slice. Secure these underside braces with 1-1/2-inch wood screws spaced every 4 inches.

Cut 2 pieces of 2-by-4 lumber to 56-inch lengths. Position one board on one side of the Lawn Care estimate Littleton, CO Care front yard Littleton cart box where the sides meet the bottom. Drive 2-inch wood screws each 4 inches throughout the 2-by-4 and into the box to produce a handle; duplicate to produce a handle on the opposite side.

Measure the distance between the two grips and trim a 1-1/2-inch diameter dowel rod to this span. Drive a 2-inch wood screw through the grips and into each end of the dowel to make a handlebar. Sand the wood with 120-grit sandpaper to avoid splinters.

Construct a 26-inch pneumatic tire on a 3/4-inch threaded rod axle, which normally requires pushing a 3/4-inch washer on the rod, followed by the tire, a second 3/4-inch washer along with a 3/4-inch lock nut to keep the tire from sliding off the rod.

Lay the axle rod assembly throughout the bottom of the cart box, lining up the tire with about 1-inch clearance between the tire and side of the box. Cut the opposite end of the threaded rod with a hacksaw to provide the same clearance to another tire. Assemble the second tire on the opposite end of the rod.

Lay the axle and tire assembly throughout the bottom of the cart box, positioned 12 inches from the front end — or one-third of the distance of the total cart underside span. Put a 33-inch bit of 1-by-2-inch lumber on both sides of the axle; this is the total width of the cart bottom, plus the 1-1/2 inches added by every 2-by-4 handle.

Secure the 1-by-2-inch lumber with 1-inch wood screws spaced every 4 inches. Cover the axle assembly and axle brace pieces with a 33-inch long bit of 1-by-4-inch lumber. Drive 1-inch wood screws through the 1-by-4-inch slice and into the 1-by-2-inch lumber.

Cut two pieces of 2-by-2-inch lumber to 13-inch lengths — half of the diameter of the bolts — to get the legs. Position them 12 inches from the rear end of the cart bottom, lined up with the sides. Drive 2 2-inch wood screws down from the inside of the cart box and into the top of each leg. The legs enable the cart to stand alone on its own when not in motion but raise off the Landscaping design San Diego design Fort Lauderdale once you lift the grips.

Measure the inside, bottom of the cart box from the vertical 2-by-2-inch corner braces along the sides to the point at which the side pieces finish. Cut 2 2-by-2-inch braces to this span and place them in the corner where the bottom meets the side.

Measure the inside distance between the vertical corner straps in the front of the cart. Cut another 2-by-2-inch slice to this length and place it where the cart bottom meets the leading piece. Drive 2-inch wood screws spaced 4 inches apart from all of the braces and into the underside.

Leave a Reply

Your email address will not be published. Required fields are marked *